Shaped, Flat, Square, Round, Fine Wire, Plated and Un-plated
ROLLS ROYCE MSRR7238 IS2
Haynes® 214 Alloy Description
Alloy 214 is a nickel-chromium-aluminum-iron alloy designed to provide the optimum in high-temperatures oxidation resistance.This alloy which is principally intended for use at temperatures of 955oC (1750oF) and above. It exhibits resistance to oxidation that far exceeds virtually all conventional heat resistant wrought alloys at these temperatures.
Mesh belts and baskets
Cobalt: 2.00 max
Tungsten: 1.00 max
Manganese: 1.00 max
Molybdenum: 1.00 max
Carbon: 0.15 max
Silicon: 0.50 max
Phosphorus: 0.15 max
Sulfur: 0.015 max
Titanium: 0.50 max
Boron: 0.015 max
Zirconium: 0.20 max
Density: 0.291 lbs/in³, 8.05 g/cm³
Electrical Resistivity: microhm-in.(microhm-cm)
70°F (21°C): 53.5 (135.9)
Specific Heat: Btu/lb.-°F(J/Kg-K):
At 70°F (21°C): 0.108(452)
Mean Coefficient of Thermal Expansion: in/in/°F (mm/m/°C):
70- 212°F (20- 100°C): 7.2 x 10-6 (13.0)
Thermal Conductivity: BTU-in/h-ft-°F (W/m-°K):
70°F (21°C): 83 (12.0)
Modulus of Elasticity: KSI (MPa)
31.6 x 10³ (218 x 10³) in tension
Melting Range: 2475-2550°F (1355-1400°C)
Mechanical Properties at Room Temperature
Ultimate Tensile Strength: 110 KSI min (758 MPa min)
Yield Strength (0.2% offset): 65 KSI min (438 MPa min)
Elongation: 25% min (gauges > .003 inches)
Hardness: Rc 30 max
Alloy 214 can be cold rolled to achieve the temper properties required by specific customers and/or manufacturing requirements. Contact Ulbrich Wire for details.
Refer to NACE (National Association of Corrosion Engineers) for recommendations.
Standard Wire Finishes
Extra Clean: Extra clean is also referred to as “bright annealed” or “bright annealed and cold rolled”
Grease (round wire only): Drawn in a heavy grease produces an “Ultra bright” finish for decorative applications
Soap (round wire only): Soap is used as a lubricant in the drawing process and is not removed. It acts as a lubricant during customer part forming operation. A soap finish is available in tempered products.
Plated: Many plating options are available.
∗Special finishes are available: Contact Ulbrich Wire Sales with special finish and plating requests.
Cut to lengths
Alloy 214 can be hardened by:
Aging at 1472°F to 1562°F
For best results refer to: SSINA’s “Welding of Stainless Steels and Other Joining Methods”
Haynes® Alloy 214 is a registered trademark of Haynes Alloys
Limitation of Liability and Disclaimer of Warranty: In no event will Ulbrich Stainless Steels and Special Metals, Inc., be liable for any damages arising from the use of the information included in this document or that it is suitable for the ‘applications’ noted. We believe the information and data provided to be accurate to the best of our knowledge but, all data is considered typical values only. It is intended for reference and general information and not recommended for specification, design or engineering purposes. Ulbrich assumes no implied or express warranty in regard to the creation or accuracy of the data provided in this document.
Copyright 2015 Ulbrich Stainless Steels & Special Metals, Inc. – Revision 6.1.2015